Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Panorama City
If your gate is sagging, scraping, or won’t close, the fix usually comes down to parts: a worn hinge, a cracked post, a stripped gear rack. Gate Installation in Panorama City and welding are our focus at Ironworks Gate Co. We replace the hardware that fails and weld the steel that breaks, on Kaiser-era tract homes and Van Nuys Boulevard storefronts alike. We know the tight driveways, the shared rights of way, and the heat that works against every metal component. Call (925) 966-4150 and a live person answers, day or night. Most repairs are done in one visit, with the price settled before we turn a single bolt.
Why Ironworks Gate Co. Is Panorama City’s Preferred Gate Parts & Welding Company
We have been doing gate work for over 42 years, and Victor Salinas leads every job with the same standard: craft it right, stand behind it. Panorama City homeowners call us because the gate that was hung in 1978 does not match any catalog spec. It was welded to fit a narrow side yard, or converted from swing to slide, or repaired once before by someone who is no longer in business. We work on what is actually there. Our technicians are background-checked and uniformed, and they treat your driveway the way they would treat their own mother’s.
Our reputation in the 91402 and 91412 ZIP codes comes from showing up when we say we will. When a gate off Van Nuys Boulevard strips its rack at 7:00 a.m. and blocks a swap-meet service alley, we get there fast because we are already working the corridor. Homeowners and business owners in Panorama City know we stock the common hinge sizes, post brackets, and gear racks locally, which means less waiting on a part from out of state.
Every job finishes with the 90-Day Done Right Promise in writing. If it is not right, Victor makes it right. No paperwork, no arguing. That is the Keystone Standard, and it applies to a 50-dollar latch repair the same as a full gate rebuild.
Our Gate Parts & Welding Services in Panorama City
Our Gate Parts & Welding team handles the full scope of hardware and steel work on driveway and estate gates. In Panorama City, four services dominate the call sheet.
Hinge Replacement
The hinges on a Kaiser-era gate have been opening and closing through 40 San Fernando Valley summers. The wide daily temperature swing flexes the steel barrel until it cracks or the pin wallows out the hole. We cut off the old hinge, weld in a heavier-barrel replacement, and reset the leaf so it swings clean without dragging. On gates off Cedros Avenue and Chase Street, we routinely find hinge posts that were never sleeved or reinforced when the original chain-link was swapped for wrought iron.
Post Replacement
Original block-wall gate posts from the 1950s have no internal steel. Decades of heat expansion crack the grout around the hinge bolts, the bolt holes crumble, and the leaf drops half an inch. We remove the old post, pour a new footing with rebar, and set a powder-coated steel post that will outlast the rest of the perimeter. For shared driveway gates where the post carries two panels, we size the footing for the combined load, not just the one panel that is sagging today, and we can add Gate Access Control - Panorama City options during the rebuild.
Rail Repair
Slide gates in Panorama City live hard. The bottom rail takes the panel’s full weight, and the guide rollers chew through the steel over time. We weld in new rail sections, straighten heat-warped frames, and rebuild the roller track so the gate rolls without binding. On conversions where a swing gate became a slide gate in the 1980s, the rail was often undersized from the start, and we correct that with heavier-gauge stock.
Custom Welding
Not every repair needs a new part. A cracked hinge gusset, a snapped picket, a ripped post cap, a broken latch strike: those are weld repairs. We do them on-site with mobile welding equipment, and we match the existing steel so the repair does not stand out. For ornamental gates with scrollwork or ring tops, we hand-shape the replacement section rather than welding in something that looks like it came from a different gate altogether.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Common Gate Parts & Welding Problems We See in Panorama City Homes
- Sagging slide-gate panels on shared driveways. The single hinge post on many Kaiser-era dual-home gates was poured shallow and never reinforced for a slide conversion. The post leans under the panel’s weight until the gate scrapes the concrete, and the operator fights the drag until something strips.
- Stripped gear racks and pinions on Van Nuys Boulevard. Commercial rolling gates near the swap-meet plazas run 50-plus cycles a day. The teeth shear where the gate changes direction, and the gate stalls half-open across the service alley.
- Crumbling block-wall gate posts from the 1950s. No internal steel means the bolt holes fail after decades of Valley heat expansion. The gate leaf drops, and the keypad deadbolt misses the strike by half an inch.
- Heat-thrown limit switches and latch strikes. When the afternoon hits 105 degrees, steel expands enough to knock auto-operator limit switches out of adjustment. The gate stops six inches short, or reverses when it should stop. We see this every summer across 91402 and 91412.
Trusted Brands We Service in Panorama City
We are trained and equipped on nine gate-automation brands, and for Panorama City Gate Motor & Opener work we most often service LiftMaster, FAAC, and Linear operators. LiftMaster units are common on the residential slide-gate conversions; FAAC shows up on heavier commercial gates along Van Nuys Boulevard; Linear operators are frequent on the older estate gates in the 91412 ZIP code. Because we carry parts for all three locally, we can often replace a gear, limit switch, or control board the same day rather than ordering and waiting. Whatever operator sits on your driveway, the fix gets made on the first visit.
Pricing for Gate Parts & Welding in Panorama City, CA
We quote every job before any work starts, in writing. A typical hinge replacement on a single wrought iron gate in Panorama City runs $180 to $340 including the part. Post replacement with a new footing runs $450 to $900 depending on post size and whether we are setting one post or rebuilding a shared-driveway pair. Bottom rail repair and welding runs $200 to $500. A stripped rack and pinion on a commercial slide gate typically runs $350 to $700 for parts and labor. The factors that move the number: post condition, panel weight, and whether the operator needs re-alignment after the weld work. For exact pricing on your gate, call (925) 966-4150. Estimates are free, and if you have a written estimate from another company, we will give you a free second opinion on it.
We Also Serve Cities Near Panorama City
Our crews work throughout the surrounding San Fernando Valley. If you are in Van Nuys, San Fernando, Granada Hills, or Reseda, we cover gate parts and welding there too, with the same 90-Day Done Right Promise on every job. Dispatch is coordinated from our Los Angeles office, and crews serve Gate Parts & Welding in Panorama City and the neighboring communities on a daily schedule, so we are never far from your driveway.
Serving Panorama City, CA - Our Local Coverage Area
We’re based in the Panorama City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Panorama City
The conversion to a slide gate happens because a swing gate needs a wide arc, and most Kaiser-era driveways are too narrow for the leaf to open without hitting the neighbor’s wall or a parked car. The first part to fail is the hinge post on the non-motor side. It was poured for a lightweight swing gate, not a sliding panel, and after 30 years of carrying the full panel weight it leans. The gate starts scraping, the operator torques against the drag, and then the rack and pinion strips. Fixing the post first is the only repair that lasts. Call (925) 966-4150 and we will assess the post, the rail, and the operator together.
Yes. We stage the work so vehicles keep moving. If we are pulling a post, the gate is unbolted and supported rather than dropped across the driveway. We park our truck on the street or in one apron, not across the shared right of way. On a typical shared gate repair in Panorama City, both neighbors can still get in and out the entire time, and we tell you exactly when access will be briefly limited before we start.
Stripped rack and pinion teeth are the number one urgent call. The gate runs 50-plus cycles a day at swap-meet plazas and food businesses, and the teeth shear where the gate changes direction. The gate stops half-open across the service alley, and the business cannot close. We respond to Van Nuys Boulevard commercial calls the same day, and we carry rack stock and pinion gears for the common operators in our service vehicles. Call (925) 966-4150 and we will get the gate rolling again.
The photocell is usually reading the gate’s own thermal expansion. In 100-plus-degree afternoons the steel rail and panel expand enough to shift the gate into the photocell’s beam path even when the gate looks fully open. The fix is re-aligning the limit switch and adjusting the photocell mounting so the beam clears the expanded steel. This is a summer-specific failure we handle constantly in 91402 and 91412. It is a quick correction, but it takes a technician who knows the heat behavior of these gates, not just the operator manual.
It depends on where the crack is and how much metal is left. A crack in the hinge barrel or gusset can often be welded strong if the surrounding steel is sound. A crack that runs through the bolt hole, or a post that is crumbling around the hinge bolts, is not weldable; the post needs replacement. We will tell you honestly which one you have. If we weld it and the weld does not hold, the 90-Day Done Right Promise covers the repair. Call (925) 966-4150 and Victor or one of our techs will evaluate the joint in person before quoting either option.
Call Ironworks Gate Co. for Gate Parts & Welding in Panorama City
The gate on your Panorama City driveway is 30 to 50 years old, and it has spent every one of those summers in Valley heat. It is going to need parts and welding at some point, and when it does, you want a crew that knows the gates on Cedros Avenue, on Van Nuys Boulevard, and on every shared driveway in between. That is us. Call (925) 966-4150 for a free estimate. A live person answers, 24 hours a day, every day. We will set a time, show up when we say, and put the price in writing before the first weld. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co.