Linear Gate Parts & Welding Nationwide

Linear Gate Parts & Welding in Northridge: What to Know First

We provide independent Linear gate parts and welding across Northridge, handling everything from snapped hinge welds to replacement of worn Linear gate rollers and latch hardware. Most Linear parts and welding jobs are completed in a single visit, and the price is settled before we turn a wrench or strike an arc. An independent Linear service provider since we first opened our doors in 1984, we carry quality OEM-spec and upgraded aftermarket parts for the Linear lines still common on Northridge driveways, and our welders can repair what no parts catalog covers. Call (925) 966-4150 and a live person answers, day or night.

Call (925) 966-4150

Key takeaways:

• Linear gate parts and welding in Northridge are handled as one job by a single team, not two separate contractors.
• We work on Linear swing and slide gate hardware: hinges, posts, rails, rollers, latch assemblies, and the weld repairs that keep them true.
• Every job is protected by our written 90-Day Done Right Promise.
• Upfront pricing agreed before any work begins. No surprises on the bill.

How Linear Products Fail - and How We Fix Them

Linear gates share a lot of DNA with the other big American brands, but the failures we see most often in Northridge are mechanical rather than electronic. The operator will usually keep running long after the metal around it has given up. That is where we come in.

• Hinge post fatigue on Linear swing gates, especially the older Linear swing arm sets: Northridge heat and the fine dust that moves through the Valley every summer work their way into hinge pins. The gate gets heavier to move, the operator strains, and eventually the post itself flexes or cracks at the weld point. We see this most on Linear-equipped gates hung on thin-wall posts. Our fix is to sleeve or replace the post, rebuild the hinge mount, and weld it so the load is spread. A fresh hinge on a tired post is a waste of your money.
• Worn Linear gate rollers on slide gates cause the chain to slap and the motor to labor: Linear slide operators, like the older Linear LS series, rely on clean, true-running rollers. When a roller bearing collapses, the gate drags, the chain tension changes, and the operator’s gear train takes the punishment. Replacing just the bad roller usually leaves the others out of plane. We replace the set, set the rail height correctly, and retension the chain so the operator is not fighting the gate.
• Broken weld at the rail-to-post connection on Linear slide installations: This is a Northridge signature failure. The ground shifts subtly through frost-and-thaw cycles even here, and a rigid weld between the rail and a concrete-embedded post eventually cracks. The gate still opens for a while, but the crack widens, the rail sags, and the gate starts to bind. We grind out the old weld, re-square the rail, and weld it back with proper gusset support so it holds.
• Latch and lock misalignment on Linear swing gates with older Linear APeX or similar actuators: The operator pulls the gate closed, but the latch plate has drifted a quarter inch and the gate bounces back. Homeowners often replace the latch, then the operator, then the board, and only then does someone check the pickup point. We find and fix the alignment issue first, then replace the latch only if it is actually worn.
• Gate ear or leaf tear at the hinge barrel: This happens when a Linear gate’s hinge bolts loosen over the years and nobody retightens them. The gate leaf wallows, the hinge ears crack, and eventually a corner of the gate droops. The repair is a proper weld repair of the ear, drilled and bushed to take the hinge pin straight again, not a bolt-through band-aid that hides the tear. We have done this repair more times than we can count on Northridge homes that date to the late 1970s and early 1980s.

Our Linear Gate Parts & Welding Process

Victor Salinas grew up not far from the old Northridge Fashion Center, and he built this company so every job follows the same unhurried sequence. There is no mystery to it, and that is the point.

1. 1
   You call (925) 966-4150. A live person answers. You describe what the gate is doing, or not doing. We ask a few questions about the gate’s age, style, and operator, and we schedule a visit at a time that works for you.
2. 2
   We inspect the gate and the Linear operator together. We look at the hinges, posts, rollers, rail, latch, and welds as one system. A Linear gate is a chain of parts; the weak link is rarely where the noise is. We find the actual cause before we quote anything.
3. 3
   You get an upfront price before any work starts. If it is a hinge rebuild and re-weld, you know the number. If we recommend an OEM-spec Linear part, you know that number too, and we explain why that part is the right call versus a cheaper substitute. No work starts without your approval.
4. 4
   We do the work. Welding is done on site in most cases. We protect the surrounding area, weld to spec, and grind and finish the repair so it looks like it belongs. If the gate needs to come off for bench work, we say so before we begin, not after.
5. 5
   We test under load. The gate cycles open and closed, under operator power, multiple times. We check the limits, the chain or arm, the latch pickup, and the welds. Then we walk it with you.
6. 6
   You get the 90-Day Done Right Promise in writing. If anything we touched is not right within 90 days, we come back and make it right. No paperwork, no arguing. That is the Keystone Standard on every Linear job we do.

What Linear Gate Parts & Welding Costs in Northridge

Linear gate parts and welding prices in Northridge depend on what failed and how much metalwork is involved. Here are the ranges we quote most often:

• Single hinge replacement with weld repair and bushing: $180-$340
• Post replacement with weld-in sleeve and concrete work: $420-$780
• Slide gate rail repair with re-weld and gusset: $260-$520
• Full roller set replacement on a Linear slide gate: $190-$410
• Custom weld repair of a cracked gate leaf or ear: $150-$400 depending on size and access
• Latch and lock realignment or replacement: $140-$310

What moves the price is access, post condition, whether the gate needs to come off its hinges, and whether we are patching a crack or rebuilding a corner. You will know the full price before we start, and the estimate is free. Call (925) 966-4150 for an exact number on your Linear gate.

Why Northridge Homeowners Call Ironworks Gate Co. for Linear Work

We have been doing this work in Northridge since 1984, which means most of the Linear gates we service today are on homes we have likely driven past a hundred times. We know which neighborhoods have the sandy soil that shifts posts on Devonshire-adjacent streets, and which older Linear installations were done with under-built hardware from the start. We do not cut corners on a weld, and we do not throw a new operator at a gate that has a structural problem underneath it.

We are trained on nine gate automation brands, and while Linear is a big part of our service area, we also work on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing equipment. That matters because plenty of Northridge gates have a Linear operator on one leaf and a different brand on the other, or a Linear operator that was replaced years ago and a gate that still has original Linear hardware. We sort it out without blinking. Background-checked, uniformed technicians show up when we say they will, and the whole job is covered by the 90-Day Done Right Promise. That has been our standard since the first gate we ever touched.

FAQs