Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Northridge Owner’s Guide

Ghost Controls keypad and intercom repair in Northridge typically costs between $195 and $385 installed, depending on whether we’re replacing the keypad module, the intercom board, or the full entry station. We stock Ghost Controls-compatible keypads, intercom modules, and wiring harnesses on our trucks, so most repairs are completed in a single visit. The usual discovery is simple: the keypad beeps but the gate won’t move, or the intercom rings the house but nobody can hear the visitor on the other end.

Call (925) 966-4150

In Northridge, we see two failure patterns more than anything else. The first is sun damage. A keypad that has faced the San Fernando Valley heat for five or six summers will develop cracked buttons, faded numbers, or a dead top row. The second is moisture intrusion. Intercoms mounted on an exposed gate pillar without a proper hood will eventually take on water during our winter rain bursts, and the speaker or the call button is usually the first thing to go. The good news is that Ghost Controls entry systems are built on simple, serviceable components, and we have been repairing them across Northridge long enough to know exactly which part to reach for. Victor Salinas grew up not far from the old Northridge Fashion Center, and he has changed enough of these keypads over the years to do the job in his sleep.

Key Takeaways

• Installed keypad replacement: $195 to $285 depending on model and wiring condition.
• Intercom module repair: $240 to $385 when the board or speaker must be replaced.
• Same-visit service: We carry Ghost Controls replacement parts on the truck, so most Northridge jobs are done the day you call.
• Upfront price: Every repair is quoted and agreed before we turn a single screw. No surprises on the bill.
• 90-Day Done Right Promise: If it is not right, we come back and make it right. Written, no arguments.

Which Ghost Controls Models This Applies To

Ghost Controls builds its entry systems around two keypad families. The first is the standard wired keypad, which appears on most single and dual gate installations across Northridge homes. These keypads are compatible with the Ghost Controls AXS-1, AXDP, and TSS1 series openers, and they use a simple four-wire connection that plugs directly into the main control board. The second family is the wireless keypad, which runs on a 9-volt battery and communicates with the opener through a small receiver box mounted near the gate motor.

Ghost Controls also offers the GHO-1 intercom module, which pairs with the keypad to let visitors call the house from the gate. This is the part that fails most often in Northridge, because the speaker cone and the call button sit inside a weather-resistant enclosure that is not weatherproof forever. The rubber seal around the button degrades in our heat, and once moisture gets in, the intercom still rings the house but the two-way audio goes dead. The compatibility gotcha to know: the GHO-1 intercom requires a Ghost Controls keypad to function. You cannot run the intercom as a standalone unit. We see this all the time after a neighbor or handyman installs a generic keypad and then wonders why the intercom never worked. If you are replacing one, you are usually replacing both, or at least checking both while the panel is open.

We are an independent gate service provider. We are not affiliated with Ghost Controls, but we work on their equipment daily and stock both OEM Ghost Controls parts and quality aftermarket equivalents that match the same specifications. For keypads and intercom modules specifically, we recommend OEM parts. The aftermarket options work, but the button layout and the wiring color codes do not always line up one-for-one with the Ghost Controls control board, and that creates unnecessary callbacks. Our job is to fix it once.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• The keypad beeps, but the gate does not move. This usually means the keypad itself is fine and the problem is in the wiring junction or the opener’s relay input. In Northridge, we find a surprising number of loose wire nuts inside the keypad housing, where the original installer did not tighten them fully.
• The intercom rings the house, but you cannot hear the visitor. That is the classic GHO-1 speaker failure. The speaker cone has dried out or taken on water. The call button still works because it is a separate circuit.
• Buttons require hard presses or multiple attempts. The membrane under the buttons loses its snap after years of sun exposure. Ghost Controls keypads on west-facing gates in Northridge fail this way faster than east-facing ones.
• Certain digits stop responding entirely. A dead digit means a broken trace inside the keypad’s circuit film. There is no field fix for a broken trace. The keypad gets replaced.
• The intercom button does not ring the house at all. This is either the button switch or the intercom module’s call relay. We test both in minutes with a multimeter, and we keep the replacement parts on the truck so we are not making a second trip.

Replacement Cost & What’s Included

Here is what Ghost Controls keypad and intercom repair costs in Northridge, installed and backed by our 90-Day Done Right Promise:

The price range comes down to two things: which generation of Ghost Controls equipment is on the gate, and the state of the low-voltage wiring. Older systems use a six-wire cable; newer ones use four. If the existing wire is serviceable, the job is straightforward. If we are chasing a short through buried conduit in a Northridge driveway, that adds a little time and a little money. None of it is hidden. We give you the price before we start, and the price we give is the price on the invoice. No discovery fees, no surprise line items.

Every Ghost Controls keypad and intercom repair we perform includes a written 90-Day Done Right Promise. If the keypad acts up, the intercom cuts out, or anything we touched is not right, we come back and fix it. No paperwork to file, no argument to win. That is the Keystone Standard, and we have applied it to every gate job in Northridge since 1984.

DIY or Call Us?

This is a low-voltage repair, so it is not dangerous in the way a high-tension spring is dangerous. You are not going to hurt yourself changing a Ghost Controls keypad. But you can absolutely hurt the control board if you cross the wrong wires, and that turns a $250 keypad swap into a $500 board replacement. If you want to do a quick check before calling us, start with the battery in the wireless keypad or the wire connections behind the wired keypad. Look for corrosion, loose wire nuts, or a keypad housing that is cracked and letting water in. Those are things any homeowner can see.

What we do not recommend is opening the Ghost Controls control board enclosure and probing terminals with a multimeter if you are not clear on what each terminal does. The box is labeled, but the wiring colors do not always match between keypad generations, and one wrong jumper can take out the whole opener. If the keypad is dead, the intercom is deaf, or the gate will not respond, call us at (925) 966-4150. We will come out, diagnose it, and give you a fixed price before any work starts.

FAQs